ホーム 製品 有機ELディスプレイ グラフィック 有機EL モジュール WEO025664A-Hotbar

2.08 インチ, 256x64 (Hotbar FPC) OLED 有機ELモジュール

型番 WEO025664A-Hotbar

►グラフィック有機ELモジュール
►結構: COG + Hotbar FPC
►サイズ:2.08インチ
►256x64 ドットマトリックス
►SSD1362コントローラー内蔵
►3V電源電圧
►1/64 duty
►インターフェース: 6800, 8080, SPI, I2C
►発光色: 白色 / 黄色 / グレースケール機能をサポートする

製品情報

WEO025664A-Hotbarはんだ付けバージョンは256x64ピクセル、対角サイズ2.08インチで作られたグラフィックCOG OLEDディスプレイです。 SSD1362ドライバーICを搭載して、6800/8080 8ビットパラレル、I2C、3線及び4線SPIインターフェースを介して通信できて、 4ビットグレースケール画像をサポートできます。 WEO025664Aのロジック電源電圧は3V電源で、1/64ドライバーデューティして、50%チェックボード電流は15mA@12Vcc(標準値)で、操作温度は-40℃~+80℃で、保存温度は-40℃~+85℃です 。

WEO025664A-Hotbarバージョンは超薄型プロファイル用のフレックステールを直接はんだ付けします。このCOG構造OLEDモジュールは1.61 mmの極薄で、 軽量で低消費電力の機種で、スマートホームアプリケーション、メーターデバイス、パーソナルケア機器、健康機器等に適します。お客様がアプリケーションに適したモジュールを選択できるように、ZIF FPC及びHotbarバージョンを提供しています。

外形図

2.08 OLED Display Module 256x64 (Hotbar FPC) - WEO025664A-Hotbar - Winstar

Data source ref: WEO025664ALAP3N00H00

製品仕様

ピン功能定義

No. 記号 説明
1 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
2 VP This pin is the segment pre-charge voltage reference pin.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
4 VDD Power supply for core logic operation.
VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.
A capacitor should be connected between VDD and VSS under all circumstances.
5 IREF This pin is the segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
When internal IREF is used, this pin should be kept NC.
6 VSS Ground pin. It must be connected to external ground.
7 VSS Ground pin. It must be connected to external ground.
8 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
9 BS0 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1, BS0 are pin select.
BS[2:0] Interface
000 4 line SPI
001 3 line SPI
110 8-bit 8080 parallel
100 8-bit 6800 parallel
010 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
10 BS1
11 BS2
12 CS This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
13 RES This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
14 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
15 R/W This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
16 RD This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
18 D1
19 D2
20 D3
21 D4
22 D5
23 D6
24 D7

規格説明

項目 仕様 単位
ドットマトリックス(解像度) 256 x 64 Dots
外形寸法 60.5 x 19.0 x 1.61 mm
有効表示エリア 51.18 x 12.78 mm
ドットサイズ 0.18 x 0.18 mm
ドットピッチ 0.2 x 0.2 mm
表示モード パッシブマトリクス
発光色 モノクロ
駆動方法 1/64 Duty
グレースケール 4 Bits
IC SSD1362
インターフェイス 3-Wire and 4-Wire SPI, I2C, 6800, 8080
サイズ 2.08 インチ

絶対最大定格

パラメーター 記号 最小値 最大値 単位
動作電源電圧 VCI -0.5 5.5 V
ロジック電源電圧 VDD -0.5 2.75 V
Display電源電圧 VCC -0.5 21 V
操作温度 TOP -40 80 °C
保存温度 TSTG -40 85 °C

電気特性

DC電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VCI 2.8 3.0 3.3 V
Display電源電圧 VCC 11.5 12 12.5 V
入力電圧(High) VIH 0.8×VCI VCI V
入力電圧(Low) VIL VSS 0.2×VCI V
出力電圧(High) VOH 0.9×VCI VCI V
出力電圧(Low) VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=12V 15 30 mA
go top
close