Home Prodotti TFT LCD Moduli TFT Standard WF24LTYAJDNN0

Moduli TFT IPS 2.4"

Modello numero WF24LTYAJDNN0

►Formato display : 240 x 320
►Dimensione : 2.4 pollici
►Direzione di visione : IPS
►Interfaccia : MCU, SPI
►A bordo Controllore: ILI9341V
►Scheda di controllo: No
►Luminosità (cd/m²): 500
►Cornice di fissaggio: No
►Touch Screen: senza pannello touch

DISEGNO

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia  

NO Simbolo Funzione I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

Specifiche generali

Articolo Dimensioni Unità
Dimensione (Diagonale) 2.4 pollici
A matrice di punti (Risoluzione) 240 × RGB × 320(TFT) punti
Dimensione del modulo 42.72(W) × 60.26(H) × 2.8(D) mm
Area attiva 36.72 × 48.96 mm
Passo del Dot 0.153 × 0.153 mm
Tipo LCD TFT, Nero, Trasmissivo
Controllo IC ILI9341V o equivalente
Direzione di visione 80/80/80/80
Proporzioni dell’area visiva (ratio) Portrait
Tipo di backlight LED, Bianco
Touch Screen senza touch screen
Superficie Bagliore (Glare)

Valori massimi assoluti

Articolo Simbolo Valore Min Valore tipico Valore massimo Unità
Temperatura di lavoro TOP -20 +70
Temperatura di stock TST -30 +80

Caratteristiche elettriche

Articolo Simbolo Valore Min Valore tipico Valore massimo Unità
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICI 6 9 mA
go top
close