2.23" 128x32 Display OLED con pannello touch capacitivo
Modello numero WEP012832A-CTP
►Tipo : grafico
►Struttura : COG + cornice + PCB
►Dimensione : 2.23 pollici
►128×32 a matrice di punti
►IC:SSD1305
►Alimentatore 3V
►1/32 duty cycle
►Interfaccia: 6800, 8080, SPI, I2C
►Touch Screen : con pannello touch capacitivo (CTP)
►Punti di tocco : 1 Dito
►Colore display: Bianco / Giallo / Blu
Descrizione
Il modello WEP012832A dispone di un elemento di estensione con pannello touch capacitivo sul modulo; ha una dimensione diagonale di 2,23" e una matrice a punti 128x32. Questo modulo OLED è integrato con il circuito integrato SSD1305, supporta le interfacce parallele 6800/8080 a 8 bit, I2C e 4-Wire SPI, con tensione di alimentazione per la logica a 3,3V (valore tipico) e duty cycle di guida 1/32. Il modello WEP012832A-CTP è dotato di un circuito integrato FT6336U per il pannello touch capacitivo sul modulo, che supporta l'interfaccia I2C, con un punto di rilevamento per il touch capacitivo.
Il modello WEP012832A-CTP è un display OLED COG con una scheda PCB sul modulo. Ci sono due metodi per le opzioni di fissaggio dei moduli sulle applicazioni dei clienti; uno è l'uso di fori di montaggio per fissare i moduli, l'altro è l'uso di perni metallici sulla scheda PCB. Inoltre, forniamo tre opzioni di collegamento dell'interfaccia per i clienti, la saldatura a barra calda, i perni metallici o FPC con connettore. Forniamo anche un mini motore a vibrazione e un buzzer opzionale.
Questo modulo OLED è adatto per applicazioni di domotica, dispositivi medici, sistemi di controllo intelligenti, ecc. Il modulo WEP012832A-CTP può funzionare a temperature comprese tra -20℃ e +70℃; il suo intervallo di temperature di conservazione va da -40℃ a +85℃.
DISEGNO
Data source ref: WEP012832AWPP3D00001
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
No. | Simbolo | Funzione | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation. | |||||||||||||||
3 | V0 | Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | D/C# | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
5 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected. When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7~14 | DB0~DB7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
15 | CS# | This pin is the chip select input. (active LOW) | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDDIO) during normal operation. |
|||||||||||||||
17,18 | BS1, BS2 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
19 | N.C. | No connection. | |||||||||||||||
20 | FG(GND) | Ground. | |||||||||||||||
21 | TP_SCK | I2C Clock | |||||||||||||||
22 | TP_SDA | I2C Data | |||||||||||||||
23 | TP_INT | Interrupt Output This pin is used as the dedicated interrupt output signal. |
|||||||||||||||
24 | TP_RST | Hardware Reset This pin is to reset hardware for this chip. |
|||||||||||||||
25 | TP_VDD | Power supply pin for only touch panel (3.3V). | |||||||||||||||
26 | VSS | Ground. | |||||||||||||||
27 | N.C. | No connection. | |||||||||||||||
28 | N.C. | No connection. |
Dati meccanici
Articolo | Dimensioni | Unità |
---|---|---|
A matrice di punti | 128 × 32 | punti |
Dimensione del modulo | 66.5 × 35.0 × 10.55 (Max) | mm |
Area attiva | 55.018 × 13.098 | mm |
Dimensioni del Dot | 0.408 × 0.388 | mm |
Passo del Dot | 0.43 × 0.41 | mm |
Modalità display | Matrice passiva | |
Colore display | Monocromatici | |
Drive Duty | 1/32 Duty | |
IC | SSD1305 | |
OLED Interfaccia | 6800, 8080, 4-Wire SPI, I2C | |
Dimensione | 2.23 pollici |
CTP IC | FT6336U |
Punti di tocco | 1 |
CTP Interfaccia | I2C |
Superficie | Bagliore (Glare) |
Valori massimi assoluti
Parameter | Simbolo | Valore Min | Valore massimo | Unità |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
Supply Voltage for Display | V0 | 0 | 16.0 | V |
Temperatura di lavoro | TOP | -20 | +70 | °C |
Temperatura di stock | TSTG | -40 | +85 | °C |
Touch Panel Controller FT6336U
Parameter | Simbolo | Valore Min | Valore massimo | Unità |
---|---|---|---|---|
Power Supply Voltage | VDD | -0.3 | 3.6 | V |
Caratteristiche elettriche
DC Caratteristiche elettriche
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 3.2 | 3.3 | 3.5 | V |
Supply Voltage for Display | V0 | - | 12.0 | 12.5 | 13.0 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | IOUT = 100uA, 3.3MHz | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | IOUT = 100uA, 3.3MHz | 0 | - | 0.1×VDD | V |
Operating Current for VDD 50% Check Board | IDD | V0 =12.5V | - | 85 | 128 | mA |
Touch Panel Controller FT6336U
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage | VDD | - | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | - | 0.7xVDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3xVDD | V |
Output High Volt. | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
Output Low Volt. | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |
Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 pollici oled, oled 2.23, oled 2.23"