Home Prodotti Display OLED Display OLED Grafici WEP012832A

128x32 OLED Grafici 2.23"

Modello numero WEP012832A

►Tipo: grafico
►Struttura: COG + cornice + PCB
►Dimensione: 2.23 pollici
►128 x 32 a matrice di punti
►IC:SSD1305
►Alimentatore 3V
►1/32 duty
►Interfaccia: 6800, 8080, SPI, I2C
►Colore display: Bianco / Giallo / Blu

Descrizione

DISEGNO

WEP012832A

Data source ref: WEP012832AWPP3N00000

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 VSS Ground.
2 VDD Power supply pin for core logic operation.
3 V0 Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
4 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
6 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected.
When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
7~14 DB0~DB7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 CS# This pin is the chip select input. (active LOW)
16 RES# This pin is reset signal input. When the pin is LOW, initialization of the chip is executed.
Keep this pin HIGH (i.e. connect to VDDIO) during normal operation.
17,18 BS2,BS1 Communicating Protocol Select.
These pins are MCU interface selection input. See the following table:
  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
19 N.C. No connection.
20 FG(GND) Ground.
21~25 N.C. No connection.
26 VSS Ground.
27 BSW Control the Piezoelectric Buzzer.
28 MSW Control the BLDC Vibration Motor.

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 128 × 32 Dots
Dimensione del modulo 66.5 × 35.0 × 9.0(Max) mm
Area attiva 55.018 × 13.098 mm
Dimensioni del Dot 0.408 × 0.388 mm
Passo del Dot 0.43 × 0.41 mm
Modalità display Matrice passiva
Colore display Monocromatici
Drive Duty 1/32 Duty
IC SSD1305
Cicalino incorporato. OBO-11241SB
Vibration Motor W0625AB001F
Interfaccia 6800, 8080, SPI, I2C
Dimensione 2.23 pollici

Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic VDD 3.0 3.3 3.5 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH IOUT = 100uA, 3.3MHz 0.9×VDD VDD V
Output Low Volt. VOL IOUT = 100uA, 3.3MHz 0 0.1×VDD V
Supply Voltage for Buzzer BSW 50% square 0.8×VDD VDD V
Supply Voltage for Vibration Motor MSW 2.7 3.3 V
Operating Current at Display with 50% Check Board IDD VDD=3.3V 90 120 mA

Valori massimi assoluti

Parameter Simbolo Valore Min Valore massimo Unità
Supply Voltage for Logic VDD -0.3 4.0 V
Temperatura di lavoro TOP -40 +80 °C
Temperatura di stock TSTG -40 +85 °C

Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 pollici oled, oled 2.23, oled 2.23"
go top
close