Home محصولات TFT LCD IPS TFT WF28JSYAJDNN0

مدل شماره WF28JSYAJDNN0

◄سایز: 2.8 اینچ
◄وضوح: 240 × 320 نقطه
◄جهت دید:IPS
◄رابط: MCU, SPI
◄IC درایور:ILI9341
◄کنترل بورد: نیست
◄روشنایی: 1000 (cd/m2)
◄سوراخ فریم: نیست
◄صفحه لمسی: نیست

شرح

 

طراحی

2.8 inch 240x320 Sunlight Readable TFT IPS LCD - WF28JSYAJDNN0 - Winstar Display

مشخصات

عملکرد پین رابط

LCM PIN Definition

NO نماد عملکرد I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(2.5 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire
9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to IOVCC or GND.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to IOVCC level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to IOVCC level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system.
Fix to GND level when not in use.
I/O
30 RESET (RESX)This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode
IM2 IM1 1M0 MCU-Interface Mode DB Pin in use
Register/Content GRAM
0 0 0 80 MCU 8-bit bus interface I D[7:0] D[7:0]
0 0 1 80 MCU 16-bit bus interface I D[7:0] D[15:0]
0 1 0 80 MCU 9-bit bus interface I D[7:0] D[8:0]
0 1 1 80 MCU 18-bit bus interface I D[7:0] D[17:0]
1 0 1 3-wire 9-bit data serial interface I SDA: In/Out
1 1 0 4-wire 8-bit data serial interface I SDA: In/Out

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at IOVCC or GND.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode
Fix to GND level when not in use.
I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDA SDA : Serial in/out signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at IOVCC or GND.
I/O
40 NC Not used, open this pin N

مشخصات عمومی

مورد ابعاد نمای کلی واحد
سایز 2.8 اینچ
وضوح 240 x RGB x 320(TFT) نقطه های
ابعاد ماژول 50.5(W) x 69.7(H) x 4.55(D) mm
ناحیه فعال 43.2 x 57.6 mm
درجه نقطه 0.18 x 0.18 mm
نوع LCD TFT, سیاه, انتقال‌دهنده
TFT IC درایور ILI9341V یا معادل آن
TFT رابط MCU/SPI
جهت دید 80/80/80/80
نسبت تصویر 3:4
نوع نور پس‌زمینه LED ,سفید
صفحه لمسی بدون پنل لمسی (صفحه لمسی)
سطح تابش خیره‌کننده

بیشینه مقادیر مجاز مطلق

مورد نماد مقدار حداقل مقدار معمول مقدار حداکثر واحد
دمای عملیاتی TOP -20 +70
دمای بسته‌بندی TST -30 +80

مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for digital IOVCC 1.65 3.3 V
Supply Voltage for analog VCI 2.5 3.3 V
Power Supply for Current ICC IOVCC=VCI
=VCC=3.0V
13 20 mA
go top
close