Home محصولات ماژول OLED OLED Knob WEO128128D-CTP-Knob

مدل شماره WEO128128D-CTP-Knob

◄نوع: گرافیک
◄ساختار: COG
◄سایز: 1.18 اینچ
◄ماتریس نقطه ای 128*128
◄کنترلگر SSD1327
◄منبع انرژی 3V
◄کار 1/128
◄رابط: SPI, I2C
◄ با پنل (صفحه) لمسی خازنی
◄Detect Point : 1 Finger
◄رنگ صفحه‌نمایش: سفید / زرد
◄Support Grayscale

شرح

 

طراحی

1.18 inch 128x128 OLED Knob with CTP Touch Panel - WEO128128D-CTP-Knob

Data source ref: WEO128128DWPP3D00E00

مشخصات

عملکرد پین رابط

No. نماد عملکرد
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select.
Bus Interface selection
BS1 Interface
0 4-line SPI
1 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 IREF This pin is the segment output current reference pin
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 DC# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, will be interpreted as data.
When the pin is pulled LOW, will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection.
11 D0 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL.
12 D1
13 D2
14 TP_SCK I2C clock signal
15 TP_SDA I2C data signal
16 TP_INT Interrupt signal
17 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
18 VSS Ground
 

Encoder PIN Definition

No. نماد عملکرد
1 FSW_A Encoder terminal signal-A
2 FSW_B Encoder terminal signal-B
3 FSW_C Encoder terminal signal-C
4 FSW_D Ground

داده مکانیکی

مورد ابعاد واحد
وضوح 128 × 128 نقطه های
ابعاد ماژول Ø56 x 21.56 mm
ناحیه فعال Ø30.0 mm
اندازه نقطه 0.210 × 0.210 mm
درجه نقطه 0.235 × 0.235 mm
حالت رنگ ماتریس غیرفعال
رنگ صفحه‌نمایش Monochrome
Drive Duty 1/128 Duty
Gray Scale 4 bits
IC SSD1327
رابط 4-line SPI , I2C
سایز 1.18 اینچ
 
CTP IC FT3268
Detect Point 1
CTP رابط I2C

بیشینه مقادیر مجاز مطلق

Parameter نماد مقدار حداقل مقدار حداکثر واحد
Supply Voltage for Operation VCI -0.3 3.6 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 19.0 V
دمای عملیاتی TOP -20 +70 °C
دمای بسته‌بندی TSTG -30 +70 °C

مشخصات الکترونیکی

DC مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for Operation VCI 2.8 3.0 3.3 V
Supply Voltage for Display VCC 8.0 14.5 15.0 V
Supply Voltage for Logic VDD 1.65 2.6 V
High Level Input VIH 0.8×VCI VCI V
Low Level Input VIL 0 0.2×VCI V
High Level Output VOH Iout = 100uA 0.9×VCI VCI V
Low Level Output VOL Iout = 100uA 0 0.1×VCI V
50% Check Board operating Current VCC =14.5V 15 30 mA
 

Touch Panel Controller FT3268

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Input High Volt. VIH 0.7×VDD VDD V
Input Low Volt. VIL -0.3 0.3×VDD V
Output High Volt. VOH IOH = 0.1mA 0.7×VDD V
Output Low Volt. VOL IOL = 0.1mA 0.3×VDD V
go top
close