Home محصولات ماژول OLED گرافیک OLED WEF012864H

مدل شماره WEF012864H

◄نوع: گرافیک(با فریم)
◄ساختار: COG+FR
◄سایز: 2.42 اینچ
◄ماتریس نقطه ای 128*64
◄کنترلگر SSD1309
◄منبع انرژی +3V
◄کار 1/64
◄رابط: 6800/8080/SPI/I2C
◄رنگ صفحه‌نمایش: سفید / زرد / آبی آسمانی / سبز / آبی

طراحی

WEF012864H
Data source ref:WEF012864HWPP3N00F00

مشخصات

عملکرد پین رابط

.Pin No نماد عملکرد
1 (NC(Vss (No connection. (ground
2 VCC .Power supply for panel driving voltage. This is also the most positive power voltage supply pin
3 VCOMH .COM signal deselected voltage level
.A capacitor should be connected between this pin and VSS
4 IREF .This pin is the segment output current reference pin
.IREF is supplied externally
A resistor should be connected between this pin and VSS to maintain the current around 10uA. Please refer to Figure 8-15 for the details of resistor value
5~12 D7~D0 .These pins are bi-directional data bus connecting to the MCU data bus
.Unused pins are recommended to tie LOW
.When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC
.When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL
13 #E/RD .This pin is MCU interface input
.When 6800 interface mode is selected, this pin will be used as the Enable (E) signal
.Read/write operation is initiated when this pin is pulled HIGH and the chip is selected
.When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected
.When serial or I2C interface is selected, this pin must be connected to VSS
14 #R/W .This pin is read / write control input pin connecting to the MCU interface
(#When 6800 interface mode is selected, this pin will be used as Read/Write (R/W
selection input. Read mode will be carried out when this pin is pulled HIGH and
.write mode when LOW
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data
.write operation is initiated when this pin is pulled LOW and the chip is selected
.When serial or I2C interface is selected, this pin must be connected to VSS
15 #D/C .This pin is Data/Command control pin connecting to the MCU
.When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command
.register
.In I2C mode, this pin acts as SA0 for slave address selection
.When 3-wire serial interface is selected, this pin must be connected to VSS
For detail relationship to MCU interface signals, refer to Timing Characteristics
16 #RES .This pin is reset signal input
.When the pin is pulled LOW, initialization of the chip is executed
.Keep this pin pull HIGH during normal operation
17 #CS .This pin is the chip select input connecting to the MCU
The chip is enabled for MCU communication only when CS# is pulled LOW (active
.(LOW
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the
following table.

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 Vdd Power supply pin for core logic operation
22~28 NC No connection
29 Vss .Ground pin. It must be connected to external ground
30 (NC(Vss (No connection. (ground

مشخصات عمومی

مورد ابعاد واحد
ماتریس نقطه ای (وضوح) 128 × 64 نقطه های
ابعاد ماژول 77.2 × 42.14 ×3.4 mm
ناحیه فعال 55.01 × 27.49 mm
اندازه نقطه 0.40 × 0.40 mm
درجه نقطه 0.43 × 0.43 mm
حالت رنگ ماتریس غیرفعال
رنگ صفحه‌نمایش Monochrome
Drive Duty 1/64 Duty
IC SSD1309
رابط 6800,8080,SPI,I2C
سایز (قطری) 2.42 اینچ

بیشینه مقادیر مجاز مطلق

Parameter نماد مقدار حداقل مقدار حداکثر واحد
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
دمای عملیاتی TOP -40 +80 °C
دمای بسته‌بندی TSTG -40 +85 °C

مشخصات الکترونیکی

DC مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13.0 13.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VCC =13V - 29 43.5 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42 inch oled, oled 2.42
go top
close