Home محصولات ماژول OLED گرافیک OLED WEA128128A

مدل شماره WEA128128A

◄نوع: گرافیک
◄ساختار: COG+PCB
◄سایز: 1.5 اینچ
◄ماتریس نقطه ای 128 * 128
◄کنترلگر SSD1327
◄منبع انرژی +3.3V+ / 5V
◄کار 1/128
◄رابط: SPI انتخاب I2C
◄رنگ صفحه‌نمایش: سفید / زرد
◄Support Grayscale

شرح

طراحی

OLED 1.5 inch,1.5 OLED Display, 1.5 inch OLED Display, 1.5 inch OLED Module - WEA128128A

Data source ref: WEA128128AWAP3N00000

مشخصات

عملکرد پین رابط

No. نماد عملکرد
1 GND This is a ground pin.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
4 D1
5 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
6 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
7 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

داده مکانیکی

مورد ابعاد واحد
ماتریس نقطه ای 128 × 128 Dots
ابعاد ماژول 34.2 × 45.5 × 3.16 mm
ناحیه فعال 26.86 × 26.86 mm
اندازه نقطه 0.185 × 0.185 mm
درجه نقطه 0.210 × 0.210 mm
حالت رنگ ماتریس غیرفعال
رنگ صفحه‌نمایش Monochrome
Drive Duty 1/128 Duty
Gray Scale 4 bits
IC SSD1327
رابط 4-Wire SPI / I2C
سایز 1.5 اینچ

بیشینه مقادیر مجاز مطلق

Parameter نماد مقدار حداقل مقدار حداکثر واحد
Supply Voltage for Logic VCC 1.65 5.5 V
دمای عملیاتی TOP -40 +80 °C
دمای بسته‌بندی TSTG -40 +85 °C

مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for Logic(3V/5V) VCC 2.8 3.3 5.2 V
Input High Volt. VIH 0.8×VCC VCC V
Input Low Volt. VIL 0 0.2×VCC V
Output High Volt. VOH 0.9×VCC VCC V
Output Low Volt. VOL 0 0.1×VCC V
50% Check Board operating Current ICC VCC=3.3V 160 320 mA
go top
close