Accueil Produits Afficheur TFT LCD TFT IPS WF101JSYAHLNB0

N° de modèle WF101JSYAHLNB0

►Dimension 10.1 pouces
►Résolution d’écran: 1024×600 points
►Vue préférentielle IPS
►Interface: LVDS
►CI pilote : EK79001HN + EK73215BCGA
►Carte de contrôle: No
►Luminosité (Cd/m²): 900
►Cadre de maintien avec points de fixation: NON
►Dalle tactile: Avec dalle tactile capacitive (PCAP)
►Detect Point : 5 Fingers

DESSIN

WF101JSYAHLNB0

SPÉCIFICATIONS

Interface

Pin No. Symbole Function
1 VCOM Common voltage
2 VDD Digital power
3 VDD Digital power
4 NC Not connect
5 Reset Global reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. (R=10KΩ,C=1μF)
6 STBYB Standby mode, normally pull high STBYB=”1”, normal operation STBYB=”0”,timing control, source driver will turn off, all output are high-Z
7 GND Digital ground
8 RXIN0- Negative LVDS differential data inputs
9 RXIN0+ Positive LVDS differential data inputs
10 GND Digital ground
11 RXIN1- Negative LVDS differential data inputs
12 RXIN1+ Positive LVDS differential data inputs
13 GND Digital ground
14 RXIN2- Negative LVDS differential data inputs
15 RXIN2+ Positive LVDS differential data inputs
16 GND Digital ground
17 RXCLKN- Negative LVDS differential clock inputs
18 RXCLKN+ Positive LVDS differential clock inputs
19 GND Digital ground
20 RXIN3- Negative LVDS differential data inputs
21 RXIN3+ Positive LVDS differential data inputs
22 GND Digital ground
23 NC Not connect
24 NC Not connect
25 GND Digital ground
26 NC Not connect
27 NC Not connect
28 SELB 6-bit/8-bit input select SELB = L , 8-bit ; SELB = H , 6-bit
29 AVDD Analog power
30 GND Digital ground
31 LED- LED Cathode
32 LED- LED Cathode
33 L/R Left or right display control
34 U/D Up / down display control
35 VGL Negative power for TFT
36 NC Not connect
37 NC Not connect
38 VGH Positive power for TFT
39 LED+ LED Anode
40 LED+ LED Anode
When L/R=”0”,set right to left scan direction.
When L/R=”1”,set left to right scan direction.
When U/D=”0”,set top to bottom scan direction.
When U/D=”1”,set bottom to top scan direction.

PCAP PIN Definition

Pin Symbole Function
1 USB_VSS System ground
2 USB_VDD 5V Power supply
3 USB_D+ Data +
4 USB_D- Data -
5 VSS System ground
6 SDA I2C data input and output
7 SCL I2C clock input
8 RST External Reset, Low is active
9 INT External interrupt to the host
10 VDDT 3.3 Power supply

Spécifications générales

Article Dimensions Unité
Screen Diagonal 10.1 pouce
Number of Pixels 1024 RGB x 600 points
Dimensions du module 235(W) x 143(H) x 8.78(D) mm
Zone active 222.72 (H) x 125.28(V) mm
Pixel pitch 0.2175(W) x 0.2088(H) mm
Type de LCD TFT, Noir, Transmissif
Interface LVDS
CI pilote EK79001HN + EK73215BCGA ou équivalent
Vue préférentielle 85/85/85/85
Rapport d'aspect 16:9
Type de rétroéclairage LED, Blanc
PCAP IC ILI2511 ou équivalent
PCAP Interface USB (I2C available)
PCAP FW Version V6.0.0.0.62.90.1.2
Avec/sans dalle tactile PCAP
Surface Reflets

Valeurs nominales maximales absolues

Article Symbole Min Typ Max Unité
Température de fonctionnement TOP -20 +70
Température de stockage TST -30 +80

Caractéristiques électroniques

Typical Operation Conditions (At Ta = 25 °C,)

Article Symbole Min Typ Max Unité
Digital Power Supply Voltage For LCD VDD 3 3.3 3.6 V
Analog Power Supply Voltage AVDD 9.89 10.2 10.5 V
Gate On Power Supply Voltage VGH 19.4 20.0 20.6 V
Gate Off Power Supply Voltage VGL -10.3 -10.0 -9.7 V
Common Power Supply Voltage VCOM 4.0 4.3 4.6 V
Input logic high voltage VIH 0.7 VDD - VDD V
Input logic low voltage VIL 0 - 0.3 VDD V
Supply PCAP USB_VDD 5V 4.4 5.0 5.5 V
I VDD 5V 97.8 120 mA
go top
close