Accueil Produits Module OLED Afficheur OLED graphique WEO004864A

N° de modèle WEO004864A

►Type: Graphique
►Structure: COG
►Dimension: 0.71 pouces
►Matrice de points 48 x 64
►Contrôleur intégré SSD1306
►Alimentation 3V
►1/64 duty
►Interface: I2C
►Couleur d'affichage: Blanc / Jaune / Bleu ciel
►Autres options FPC disponibles dans le tableau ci-dessous

DESCRIPTION


   Options de FPC

 

DESSIN

Winstar Display - 0.71" Graphic OLED 48x64, 0.71 oled

Data source ref: WEO004864AWPP3N00000

SPÉCIFICATIONS

Fonction PIN sur l'interface

No. Symbole Function
1 C2N Positive Terminal of the Flying Inverting Capacitorr Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
11 SDA
12 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and Vss to maintain the IREF current at a maximum of 30uA.
When internal IREF is used, this pin should be kept NC
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Données mécaniques

Article Dimensions Unité
Matrice de points 48 × 64 Dots
Module dimension 13.90 × 22.0 × 1.26 mm
Zone active 10.54 × 14.70 mm
Pixel Size 0.198 × 0.208 mm
Pixel Pitch 0.220 × 0.230 mm
Display Mode Matrice passive
Couleur d'affichage Monochrome
Drive Duty 1/64 Duty
IC SSD1306
Interface I2C
Diagonale 0.71 pouces

Valeurs nominales maximales absolues

Parameter Symbole Min Max Unité
Supply Voltage for Logic VDD 0 4 V
Supply Voltage for Display VCC 0 15 V
Température de fonctionnement TOP -40 +80 °C
Température de stockage TSTG -40 +85 °C

Caractéristiques électroniques

Article Symbole État Min Typ Max Unité
Supply Voltage for Logic VDD 2.8 3 3.3 V
Supply Voltage for Display VCC 7.0 7.5 8.0 V
Input High Volt. VIH 0.8 xVDD VDD V
Input Low Volt. VIL 0 0.2 xVDD V
Output High Volt. VOH 0.9 xVDD VDD V
Output Low Volt. VOL 0 0.1 xVDD V
50% Check Board operating Current ICC VCC=7.5V 15 25.0 mA

Options de FPC:

Image FPC Length PIN pitch ZIF FPC or HOTBAR FPC Interface FPC No. Create Date
FPC2000701401XXXXX00_WEO004864ALPP3N00000 16.0 14 0.7 HOTBAR FPC I2C FPC2000701401XXXXX00 20160603
FPC2070001401XXXXX02_WEO004864AWPP3N00H00 11.2 14 0.7 HOTBAR FPC I2C FPC2070001401XXXXX02 20180307

Search keyword: 48x64 oled, oled 48x64, 0.71 oled, 0.71 " oled, 0.71 inch oled, oled 0.71 , oled 0.71 "
go top
close