Module d'Affichage LCD COG 128x64 - WO12864D2

Module d'Affichage LCD COG 128x64

N° de modèle WO12864D2

►Afficheur COG 128x64
►Afficheur graphique
►IC: ST7565P
►Alimentation 3.3V
►Taux de rafraichissement 1/64 duty cycle
►Interface : 6800/8080/SPI

Téléchargement PDF

DEMO CODE Ajouter à demande

PRÉC. Retour à la liste SUIVANT

DESSIN

Data source ref: WO12864D2-TFH#

SPÉCIFICATIONS

Fonction PIN sur l'interface

Pin No.	Symbole	Description
1	/CS1	This is the chip select signal. When /CS1 = “L” , then the chip select becomes active, and data/command I/O is enabled.
2	/RES	When /RES is set to “L” , the settings are initialized.
3	A0	This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or a command. A0 = “H”: Indicates that D0 to D7 are display data. A0 = “L”: Indicates that D0 to D7 are control data.
4	/WR(R/W)	When connected to an 8080 MPU, this is active LOW. (R/W) This terminal connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write.
5	/RD(E)	When connected to an 8080 MPU, this is active LOW. (E) This pin is connected to the /RD signal of the 8080 MPU, and the ST7565P series data bus is in an output status when this signal is “L”. When connected to a 6800 Series MPU, this is active HIGH. This is the 6800 Series MPU enable clock input terminal.
6	DB0	This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data Bus.
7	DB1
8	DB2
9	DB3
10	DB4
11	DB5
12	DB6
13	DB7
14	VDD	Shared with the MPU power supply terminal VDD. ( 3.3 V )
15	VSS	This is a 0V terminal connected to the system GND.
16	VOUT	DC/DC voltage converter. Connect a capacitor between this terminal and VSS.
17	CAP5+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
18	CAP3+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
19	CAP1-	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1+ terminal.
20	CAP1+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
21	CAP2+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
22	CAP2-	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2+ terminal.
23	CAP4+	DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
24	VRS	This is the externally-input VREG power supply for the LCD power supply voltage regulator.
25	V4	This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using an op. amp. Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below. V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧Vss When the power supply turns ON, the internal power supply circuits produce the V1 to V4 voltages shown below. The voltage settings are selected using the LCD bias set command.
26	V3
27	V2
28	V1
29	V0
30	VR	Output voltage regulator terminal. Provides the voltage between VDD and V5 through a resistive voltage divider. IRS = “L” : the V5 voltage regulator internal resistors are not used . IRS = “H” : the V5 voltage regulator internal resistors are used .
31	C86	This is the MPU interface switch terminal. C86 = “H”: 6800 Series MPU interface. C86 = “L”: 8080 MPU interface.
32	P/S	This is the parallel data input/serial data input switch terminal. P/S = “H”: Parallel data input. P/S = “L”: Serial data input. The following applies depending on the P/S status: When P/S = “L”, D0 to D5 may be “H”, “L” or Open. RD (E) and WR (R/W) are fixed to either “H” or “L”. With serial data input, It is impossible read data from RAM .
33	/HPM	This is the power control terminal for the power supply circuit for liquid crystal drive. HPM = “H”: Normal mode HPM = “L”: High power mode
34	IRS	This terminal selects the resistors for the V5 voltage level adjustment. IRS = “H”: Use the internal resistors IRS = “L”: Do not use the internal resistors. The V5 voltage level is regulated by an external resistive voltage divider attached to the VR terminal

Spécifications générales

Article	Dimensions	Unité
Matrice de points (Résolution)	128 x 64 dots	－
Dimensions du module	90.0 x 52.8 x 6.6	mm
Zone d'affichage	70.7 x 38.8	mm
Zone active	66.52 x 33.24	mm
Taille des points	0.48 x0.48	mm
Pas des points	0.52 x 0.52	mm
Duty	1/64 , 1/9 Bias
Type de rétroéclairage	LED
IC	ST7565P
Interface	6800/8080/4-Line SPI

Valeurs nominales maximales absolues

Article	Symbole	Valeur min	Valeur type	Valeur max	Unité
Température de fonctionnement	TOP	-20	－	+70	℃
Température de stockage	TST	-30	－	+80	℃
Power Supply Voltage	VDD	-0.3	－	3.6	V
Power supply voltage (VDD standard)	V0, VOUT	-0.3	－	14.5	V
Power supply voltage (VDD standard)	V1, V2, V3, V4	-0.3	－	V0+0.3	V

Caractéristiques électroniques

Article	Symbole	État	Valeur min	Valeur type	Valeur max	Unité
Supply Voltage For Logic	VDD-VSS	－	2.7	3.0	3.3	V
Supply Voltage For LCM	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	10.0 9.8 9.6	10.2 10.0 9.8	10.4 10.2 10.0	V V V
Input High Volt.	VIH	－	0.8 VDD	－	VDD	V
Input Low Volt.	VIL	－	Vss	－	0.2 VDD	V
Output High Volt.	VOH	－	0.8 VDD	－	VDD	V
Output Low Volt.	VOL	－	Vss	－	0.2VDD	V
Supply Current (LED backlight is not included)	IDD	VDD=3.0V		0.6	1	mA

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd