Home Productos Pantalla TFT Modulo TFT estándares WF24LTYAJDNN0

IPS Pantalla TFT 2.4 pulgada

Modelo Nº WF24LTYAJDNN0

►Formato de presentación : 240 x 320
►Tamaño : 2.4 pulgada
►Dirección de la vista : IPS
►Interfaz : MCU, SPI
►Controlador integrado: ILI9341V
►Placa de control: No
►Brillo (cd/m²): 500
►Agujero del bastidor : No
►Pantalla táctil : Sin panel táctil

DIBUJO

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

ESPECIFICACIONES

Función interfaz Pin

NO Símbolo Función I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

Especificaciones generales

Elemento Dimensión Unidad
Tamaño (Diagonal) 2.4 pulgada
Matriz de puntos (Resolución) 240 × RGB × 320(TFT) puntos
Dimensión del módulo 42.72(W) × 60.26(H) × 2.8(D) mm
zona activa 36.72 × 48.96 mm
Distancia entre puntos 0.153 × 0.153 mm
Tipo de LCD TFT, Negro, Transmisivo
IC de Controlador ILI9341V  o equivalente
Dirección de la vista 80/80/80/80
Relación de aspecto Portrait
Tipo de retroiluminación LED, Blanco
Pantalla táctil Sin pantalla táctil
Superficie Deslumbramiento

Valores nominales máximos absolutos

Elemento Símbolo Valor mín. Valor típico Valor máx. Unidad
Temperatura de funcionamiento TOP -20 +70
Temperatura de almacenamiento TST -30 +80

Características electrónicas

Elemento Símbolo Valor mín. Valor típico Valor máx. Unidad
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICI 6 9 mA
go top
close