10.1" 1024x600 LVDS IPS TFT Display
Modelo Nº WF101JTYAHLNN0
►Tamaño : 10.1 pulgada
►Resolución : 1024×600 pontos
►Dirección de la vista : IPS
►Interfaz : LVDS
►Controlador IC : EK79001HN + EK73215BCGA
►Placa de control : No
►Brillo (cd/m2) : 500
►Agujero del bastidor : No
►Pantalla táctil : Sin panel táctil
DIBUJO
ESPECIFICACIONES
Función interfaz Pin
| Pin No. | Símbolo | Función |
|---|---|---|
| 1 | VCOM | Common voltage |
| 2 | VDD | Digital power |
| 3 | VDD | Digital power |
| 4 | NC | Not connect |
| 5 | Reset | Global reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. (R=10KΩ，C=1μF) |
| 6 | STBYB | Standby mode, normally pull high STBYB=”1”, normal operation STBYB=”0”,timing control, source driver will turn off, all output are high-Z |
| 7 | GND | Digital ground |
| 8 | RXIN0- | Negative LVDS differential data inputs |
| 9 | RXIN0+ | Positive LVDS differential data inputs |
| 10 | GND | Digital ground |
| 11 | RXIN1- | Negative LVDS differential data inputs |
| 12 | RXIN1+ | Positive LVDS differential data inputs |
| 13 | GND | Digital ground |
| 14 | RXIN2- | Negative LVDS differential data inputs |
| 15 | RXIN2+ | Positive LVDS differential data inputs |
| 16 | GND | Digital ground |
| 17 | RXCLKN- | Negative LVDS differential clock inputs |
| 18 | RXCLKN+ | Positive LVDS differential clock inputs |
| 19 | GND | Digital ground |
| 20 | RXIN3- | Negative LVDS differential data inputs |
| 21 | RXIN3+ | Positive LVDS differential data inputs |
| 22 | GND | Digital ground |
| 23 | NC | Not connect |
| 24 | NC | Not connect |
| 25 | GND | Digital ground |
| 26 | NC | Not connect |
| 27 | NC | Not connect |
| 28 | SELB | 6-bit/8-bit input select SELB = L , 8-bit ; SELB = H , 6-bit |
| 29 | AVDD | Analog power |
| 30 | GND | Digital ground |
| 31 | LED- | LED Cathode |
| 32 | LED- | LED Cathode |
| 33 | L/R | Left or right display control |
| 34 | U/D | Up / down display control |
| 35 | VGL | Negative power for TFT |
| 36 | NC | Not connect |
| 37 | NC | Not connect |
| 38 | VGH | Positive power for TFT |
| 39 | LED+ | LED Anode |
| 40 | LED+ | LED Anode |
When L/R=”1”,set left to right scan direction.
When U/D=”0”,set top to bottom scan direction.
When U/D=”1”,set bottom to top scan direction.
Especificaciones generales
| Elemento | Dimensión | Unidad |
|---|---|---|
| Tamaño | 10.1 | pulgada |
| Matriz de puntos | 1024 RGB x 600 | dots |
| Dimensión del módulo | 235(W) x 143(H) x 5.05(D) | mm |
| zona activa | 222.72 (H) x 125.28(V) | mm |
| Distancia entre puntos | 0.2175(W) x 0.2088(H) | mm |
| Tipo de LCD | TFT, Negro, Transmisivo | |
| Interfaz | LVDS | |
| Controlador IC | EK79001HN + EK73215BCGA o equivalente | |
| Dirección de la vista | 85/85/85/85 | |
| Relación de aspecto | 16:9 | |
| Tipo de retroiluminación | LED, Blanco | |
| Con o sin panel táctil | Sin panel táctil | |
| Superficie | Pantalla antirreflectante | |
Valores nominales máximos absolutos
| Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|
| Temperatura de funcionamiento | TOP | -20 | － | 70 | ℃ |
| Temperatura de almacenamiento | TST | -20 | － | 70 | ℃ |
Características electrónicas
Typical Operation Conditions (At Ta = 25 °C,)
| Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
|---|---|---|---|---|---|
| Digital Power Supply Voltage For LCD | VDD | 3 | 3.3 | 3.6 | V |
| Analog Power Supply Voltage | AVDD | 9.89 | 10.2 | 10.5 | V |
| Gate On Power Supply Voltage | VGH | 19.4 | 20.0 | 20.6 | V |
| Gate Off Power Supply Voltage | VGL | -10.3 | -10.0 | -9.7 | V |
| Common Power Supply Voltage | VCOM | 4.0 | 4.3 | 4.6 | V |
| Input logic high voltage | VIH | 0.7 VDD | - | VDD | V |
| Input logic low voltage | VIL | 0 | - | 0.3 VDD | V |
