Pantalla OLED Con Táctil Capacitivo 2.23", 128x32 puntos
Modelo Nº WEP012832A-CTP
►Tipo : Gráfico
►Estructura : COG + marco + PCB
►Tamaño : 2.23"
►Matriz de puntos 128×32
►IC:SSD1305
►Fuente de alimentación de 3V
►1/32 duty cycle
►Interfaz: 6800, 8080, SPI, I2C
►Pantalla táctil : Con panel táctil capacitivo (CTP)
►Puntos táctiles : 1 Puntos
►Color de la pantalla: Blanco / Amarillo / Azul
Descripción
El modelo WEP012832A cuenta con un elemento de extensión con Panel Táctil Capacitivo en el módulo; tiene un tamaño diagonal de 2.23 pulgadas y está compuesto por una matriz de puntos de 128x32. Este módulo OLED está integrado con el circuito integrado SSD1305; admite una interfaz paralela de 8 bits 6800/8080, I2C y SPI de 4 cables, con un voltaje de alimentación lógica de 3.3V, una corriente de tablero del 50% de 85mA a 3.3VDD (valor típico) y un deber de conducción de 1/32. El voltaje de suministro para la lógica es de 3.0V a 5.0V (VDD). Este modelo tiene un Panel Táctil Capacitivo en el módulo; está integrado con el circuito integrado FT6336U que admite una interfaz I2C, un punto de detección para la pantalla táctil capacitiva.
El modelo WEP012832A-CTP es una pantalla OLED COG con una PCB en el módulo. Hay dos métodos de opciones para fijar los módulos en las aplicaciones de los clientes; uno es usar orificios de montaje para fijar los módulos, y el otro es usar pines metálicos en la placa de circuito. Además, proporcionamos tres opciones de conexión de interfaz para que los clientes elijan, soldadura de barra caliente, pines metálicos o FPC con conector. También proporcionamos un motor de vibración miniatura y un zumbador opcional.
Este módulo OLED es adecuado para aplicaciones de hogar inteligente, dispositivos médicos, sistemas de control inteligente, etc. El módulo WEP012832A-CTP puede operar a temperaturas de -20°C a +70°C; su rango de temperaturas de almacenamiento varía de -40°C a +85°C.
DIBUJO
Data source ref: WEP012832AWPP3D00001
ESPECIFICACIONES
Función interfaz Pin
No. | Símbolo | Función | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation. | |||||||||||||||
3 | V0 | Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | D/C# | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
5 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected. When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7~14 | DB0~DB7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
15 | CS# | This pin is the chip select input. (active LOW) | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDDIO) during normal operation. |
|||||||||||||||
17,18 | BS1, BS2 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
19 | N.C. | No connection. | |||||||||||||||
20 | FG(GND) | Ground. | |||||||||||||||
21 | TP_SCK | I2C Clock | |||||||||||||||
22 | TP_SDA | I2C Data | |||||||||||||||
23 | TP_INT | Interrupt Output This pin is used as the dedicated interrupt output signal. |
|||||||||||||||
24 | TP_RST | Hardware Reset This pin is to reset hardware for this chip. |
|||||||||||||||
25 | TP_VDD | Power supply pin for only touch panel (3.3V). | |||||||||||||||
26 | VSS | Ground. | |||||||||||||||
27 | N.C. | No connection. | |||||||||||||||
28 | N.C. | No connection. |
Datos mecánicos
Elemento | Dimensión | Unidad |
---|---|---|
Matriz de puntos | 128 × 32 | Puntos |
Dimensión del módulo | 66.5 × 35.0 × 10.55(Max) | mm |
zona activa | 55.018 × 13.098 | mm |
Tamaño del punto | 0.408 × 0.388 | mm |
Distancia entre puntos | 0.43 × 0.41 | mm |
Modo de visualización | Matriz pasiva | |
Color de la pantalla | Monocromos | |
Drive Duty | 1/32 Duty | |
IC | SSD1305 | |
OLED interfaz | 6800, 8080, 4-Wire SPI, I2C | |
Tamaño | 2.23 pulgada |
CTP IC | FT6336U |
Puntos táctiles | 1 |
CTP interfaz | I2C |
Superficie | Deslumbramiento |
Valores nominales máximos absolutos
Parameter | Símbolo | Valor mín. | Valor máx. | Unidad |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
Supply Voltage for Display | V0 | 0 | 16.0 | V |
Temperatura de funcionamiento | TOP | -20 | +70 | °C |
Temperatura de almacenamiento | TSTG | -40 | +85 | °C |
Panel táctil Controlador FT6336U
Parameter | Símbolo | Valor mín. | Valor máx. | Unidad |
---|---|---|---|---|
Power Supply Voltage | VDD | -0.3 | 3.6 | V |
Características electrónicas
DC Características electrónicas
Elemento | Símbolo | Condición | Valor mín. | Típico | Valor máx. | Unidad |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 3.2 | 3.3 | 3.5 | V |
Supply Voltage for Display | V0 | - | 12.0 | 12.5 | 13.0 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | IOUT = 100uA, 3.3MHz | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | IOUT = 100uA, 3.3MHz | 0 | - | 0.1×VDD | V |
Operating Current for VDD 50% Check Board | IDD | V0 =12.5V | - | 85 | 128 | mA |
Panel táctil Controlador FT6336U
Elemento | Símbolo | Condición | Valor mín. | Típico | Valor máx. | Unidad |
---|---|---|---|---|---|---|
Supply Voltage | VDD | - | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | - | 0.7xVDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3xVDD | V |
Output High Volt. | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
Output Low Volt. | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |
Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 pulgada oled, oled 2.23, oled 2.23"