Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEO128128D-CTP

1,18 Zoll 128x128 Rundes OLED Display mit kapazitivem Touchscreen

Modellnummer WEO128128D-CTP

►1,18 Zoll OLED
►Rundes OLED Display
►Typ: Grafik
►Bauweise: COG
►128x128 Punktmatrix
►Integrierter Controller SSD1327
►3-V-Stromversorgung
►1/128 duty
►Schnittstelle: SPI, I2C
►kapazitiven Touchscreen
►die Farbe des Displays: Weiß / Gelb / Himmelblau (have high MOQ) / Support Grayscale

Zeichnung

1.18" 128x128 Round OLED Display Module with Touch Screen - WEO128128D-CTP
Data source ref: WEO128128DWPP3D00001

Technische Daten

Schnittstelle Pin-Funktion

No. Symbol Beschreibung
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select.
Bus Interface selection
BS1 Interface
0 4-line SPI
1 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 IREF This pin is the segment output current reference pin
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 DC# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, will be interpreted as data.
When the pin is pulled LOW, will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection.
11 D0 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL.
12 D1
13 D2
14 TP_SCK I2C clock signal
15 TP_SDA I2C data signal
16 TP_INT Interrupt signal
17 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
18 VSS Ground

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 x 128 Punkte
Abmaße der modul Ø50,5 × 5,0 mm
Aktiver Bereich Ø30,0 mm
Punktgröße 0,210 × 0,210 mm
Punktabstand 0,235 × 0,235 mm
Display Mode Passive Matrix
Display Color Monochromes
Drive Duty 1/128Duty
Gray Scale 4 bits
IC SSD1327
Schnittstelle 4-line SPI , I2C
Größe (Diagonale) 1,18 Zoll
PCAP IC IT7259
Detect Point 1
PCAP Schnittstelle I2C
PCAP Surface Hardness 6H

Absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Supply Voltage for Operation VCI -0,3 4,0 V
Supply Voltage for Logic VDD -0,5 2,75 V
Supply Voltage for Display VCC -0,5 19,0 V
Betriebstemperatur TOP -20 +50 °C
Lagertemperatur TSTG -30 +70 °C

elektronische Eingenschaften

DC elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage for Logic VCI 2,8 3,0 3,3 V
Supply Voltage for Display VCC 14,0 14,5 15,0 V
High Level Input VIH 0,8×VCI VCI V
Low Level Input VIL 0 0,2×VCI V
High Level Output VOH Iout = 100uA 0,9×VCI VCI V
Low Level Output VOL Iout = 100uA 0 0,1×VCI V
50% Check Board operating Current VCC =14,5V 24 36 mA

 

Touch Panel Controller IT7259

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Input High Volt. VIH COMS 1,2 V
Input Low Volt. VIL COMS 0,5 V
Output High Volt. VOH IOH = 2mA 2,4 V
Output Low Volt. VOL IOL = 2mA 0,4 V
go top
close