Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEP012832A-CTP

2,23 Zoll 128x32 OLED-Anzeigen mit kapazitiven Touchscreen

Modellnummer WEP012832A-CTP

►Typ: Grafik
►Bauweise: COG+FR+PCB
►Größe: OLED 2,23 Zoll
►128×32 Punktmatrix OLED
►Integrierter Controller SSD1305Z
►3-V-Stromversorgung
►1/32 duty cycle
►Schnittstelle: 6800, 8080, SPI, I2C
►Touchscreen: Touchscreen Kapazitiv

Beschreibung

  • WEP012832AWPP3D00000 : Weiß

Zeichnung

2.23 128x32 Capacitive Touch OLED Display - WEP012832A-CTP - Winstar Display

Technische Daten

Schnittstelle Pin-Funktion

No. Symbol Funktion
1 VSS Ground.
2 VDD Power supply pin for core logic operation.
3 V0 Keep float (i.e. disable). Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
4 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
6 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO)
and the chip is selected.
When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin must be connected to VSS.
7~14 DB0~DB7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 CS# This pin is the chip select input. (active LOW)
16 RES# This pin is reset signal input. When the pin is LOW, initialization of the chip is executed.
Keep this pin HIGH (i.e. connect to VDDIO) during normal operation.
17,18 BS2,BS1 Communicating Protocol Select.
These pins are MCU interface selection input. See the following table:
  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
19 N.C. No connection.
20 FG(GND) Ground.
21 TP_SCK I2C Clock
22 TP_SDA I2C Data
23 TP_INT Interrupt Output
This pin is used as the dedicated interrupt output signal.
24 TP_RST Hardware Reset
This pin is to reset hardware for this chip.
25 TP_VDD Power supply pin for only touch panel (3.3V).
26 VSS Ground.
27 BSW Control the Piezoelectric Buzzer.
28 MSW Control the BLDC Vibration Motor.

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 × 32 Punkte
Abmaße der modul 66,5 × 35,0 × 10,55(Max) mm
Aktiver Bereich 55,018 × 13,098 mm
Pixelgröße 0,408 × 0,388 mm
Pixelabstand 0,43 × 0,41 mm
der Anzeigemodus Passive Matrix
die Farbe des Displays Monochrome
Drive Duty 1/32 Duty
IC SSD1305Z
OLED Schnittstelle 6800, 8080, SPI, I2C
CTP Schnittstelle I2C
Größe 2,23 Zoll

elektronische Eingenschaften

DC elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage for Logic VDD 3,2 3,3 3,5 V
Supply Voltage for Display V0 12,0 12,5 13,0 V
Input High Volt. VIH 0,8×VDD VDD V
Input Low Volt. VIL 0 0,2×VDD V
Output High Volt. VOH IOUT = 100uA, 3.3MHz 0,9×VDD VDD V
Output Low Volt. VOL IOUT = 100uA, 3.3MHz 0 0,1×VDD V
Operating Current for VDD IDD V0 =12.5V - 90 120 mA
Supply Voltage for Buzzer BSW VDD=5.0V
1/2 square
0,8×VDD VDD V
Supply Voltage
for Vibration Motor
MSW 2,7 3,3 V

absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Supply Voltage for Logic VDD -0,3 4,0 V
Supply Voltage for Display V0 0 16,0 V
Betriebstemperatur TOP -40 +80 °C
Lagertemperatur TSTG -40 +85 °C

Search keyword: 128x32 oled, oled 128x32, 2.23 oled, 2.23" oled, 2.23 Zoll oled, oled 2.23, oled 2.23"
go top
close