Home Products TFT LCD Standard TFT Color Display WF57VTIACDNG0

5.7 inch TFT LCD Touch Display (PCAP)

Model No. WF57VTIACDNG0

►Size : 5.7”
►Resolution : 320 x 240 dots
►View Direction : 12H
►Interface : RGB
►Driver IC:HX8218+HX8615
►Control-Board : No
►Brightness (cd/m²) : 400
►Frame Through Hole : Yes
►Touch Screen : Projected Capacitive Touch Screen (PCAP)
►Detect Point : 5 Fingers
►O-Film : Option

Description

This 5.7" WF57VTIACDNG0 is standard TFT LCD module with Projected Capacitive Touch Screen.  This TFT-LCD touch display dimension is 160 x 109 mm and AA size of 115.2 x 86.40 mm.  Operating temperature ranges include standard -20 to +70℃ and wide -30 to +80℃. 

DRAWING

5.7 inch Display, TFT LCD Touch Display - WF57VTIACDNG0

SPECIFICATIONS

Interface

LCM PIN Definition

Pin Symbol Function
1 IF1 Input data format control
2 IF2 Input data format control
3 POL Polarity Signal connect to VCOM driving circuit.
4 RESET Hardware reset
5 SPENA Chip select
6 SPCL Serial Clock
7 SPDA Serial Data
8 B0 Blue Data bit
9 B1 Blue Data bit
10 B2 Blue Data bit
11 B3 Blue Data bit
12 B4 Blue Data bit
13 B5 Blue Data bit
14 B6 Blue Data bit
15 B7 Blue Data bit
16 G0 Green Data bit
17 G1 Green Data bit
18 G2 Green Data bit
19 G3 Green Data bit
20 G4 Green Data bit
21 G5 Green Data bit
22 G6 Green Data bit
23 G7 Green Data bit
24 R0 Red Data bit
25 R1 Red Data bit
26 R2 Red Data bit
27 R3 Red Data bit
28 R4 Red Data bit
29 R5 Red Data bit
30 R6 Red Data bit
31 R7 Red Data bit
32 Hsync Horizontal synchronous signal
33 Vsync Vertical synchronous signal
34 Data CLK Dot data clock
35 AVDD(analog) Analog power: 4.5V~5.5V
36 AVDD(analog) Analog power: 4.5V~5.5V
37 VCC(Digital) Digital power: 3V~3.6V
38 VCC(Digital) Digital power: 3V~3.6V
39 NPC NTSC/PAL mode Auto detection result H:NTSC/L:PAL
40 VGL Gate off power
41 VGL Gate off power
42 UD Up/down selection
43 VGH Gate on power
44 LRC Shift direction of device internal shift register control.
45 GND System ground pin of the IC.
Connect to system ground.
46 VCOM VCOM driving input
47 VCOM VCOM driving input
48 ENB Signal to settle the horizontal display position
49 GND System ground pin of the IC.
Connect to system ground.
50 GND System ground pin of the IC.
Connect to system ground.

PCAP PIN Definition

Pin Symbol Function
1 VSS System ground pin of the IC. Connect to system ground.
2 VDDT Power Supply : +3.3V
3 SCL I2C clock input
4 NC No connect
5 SDA I2C data input and output
6 NC No connect
7 /RST External Reset, Low is active
8 NC No connect
9 /INT External interrupt to the host
10 VSS System ground pin of the IC. Connect to system ground.

General Specifications

Item Dimension Unit
Size 5.7 inch
Dot Matrix 320 × RGB × 240 (TFT) dots
Module dimension 160(W) × 109(H) × 9.985 (D) mm
Active area 115.2 × 86.40 mm
Dot pitch 0.12 × 0.36 mm
LCD type TFT, Normally White, Transmissive
View Direction 12 o'clock
Gray Scale Inversion Direction 6 o'clock
TFT Interface 24-bit RGB
TFT Drive IC HX8218+HX8615 or equivalent
Aspect Ratio 4:3
Backlight Type LED, Normally White
PCAP FW Version 0x07.0x00.0x00.0x00.0xA2.0x01.0x57.0x00
PCAP IC ILI2130 or Equivalent
PCAP Interface I2C
PCAP Resolution 16384*16384
Touch Panel Projected Capacitive Touch Panel (PCAP)
Surface Glare

Absolute Maximum Ratings

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80

Electrical Characteristics

Item Symbol Min Typ Max Unit
Supply Voltage For LCM VCC 3.2 3.3 3.4 V
Supply Current For LCM ICC 30 45 mA
Supply CTP VDDT 3.1 3.3 3.5 V
ICTP 56 84 mA
Input High Volt. VIH 0.7 VCC VCC V
Input Low Volt. VIL 0 0.3 VCC V
LCD Driving
Supply Voltage
VGH 15 16 17 V
VGL -6 -5 -4 V
VCOMH 4.5 V
VCOML -0.5 V
AVDD 4.5 5.0 5.5 V

Search keyword: tft 5.7, tft 5.7", 5.7 tft lcd, 5.7" tft lcd, 5.7 inch tft lcd, tft lcd 5.7, 5.7 tft display, 5.7" tft display, 5.7 inch tft display, tft display 5.7, tft display 5.7"
go top
close