نزل المنتجات وحدات OLED وحدات OLED Touch WEN025664B-CTP

رقم الموديل WEN025664B-CTP

◄النوع: جرافيك
◄الهيكل: COF+FR+PCB
◄الحجم: 3.12 بوصة
◄مصفوفة نقطية 256×64
◄وحدة تحكم مدمجة SSD1322
◄مزود طاقة +3 فولت
◄1/64 دورة الحمولة
◄الواجهة: 6800, 8080 ,SPI
◄شاشة اللمس: بلوحة (شاشة) لمس سعويه (CTP)
◄Detect Point : 1 Finger
◄لون العرض: أبيض / أصفر / أزرق سماوي / أخضر
◄Support Grayscale

الرسم

3.12 inch 256x64 COF Touch OLED Display with PCB +Frame - WEN025664B-CTP
 

Data source ref: WEN025664BWPP3D00000

المواصفات

وظيفة دبوس واجهة التوصيل

Pin Number الرمز I/O الوصف
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Bus Interface electioin
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

البيانات الميكانيكية

العنصر الأبعاد الوحدة
دقة العرض 256 × 64 نقطة
أبعاد الوحدة 89.2 × 44.0 × 7.98 mm
المنطقة النشطة 76.78 × 19.18 mm
حجم النقطة 0.278 × 0.278 mm
درجة النقطة 0.3 × 0.3 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 Duty
Gray Scale 4 bits
OLED IC SSD1322 (COF)
OLED الواجهة 6800, 8080, SPI
الحجم 3.12 بوصة
CTP IC FT6336U
Detect Point 1
CTP الواجهة I2C
السطح توهج

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Display VDD -0.3 4 V
درجة حرارة التشغيل TOP -20 +70 °C
درجة حرارة التخزين TSTG -30 +80 °C

المميزات الإلكترونية

DC المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 150 300 mA
go top
close