نزل المنتجات وحدات OLED وحدات OLED Touch WEP012864Q-CTP

رقم الموديل WEP012864Q-CTP

◄النوع: جرافيك
◄االهيكل: COG+FR+PCB
◄الحجم: 2.7 بوصة
◄مصفوفة نقطية 128*64
◄وحدة تحكم مدمجة SSD1309
◄مزود طاقة +3 فولت
◄1/64 حمولة
◄الواجهة: 6800/8080/SPI/I2C
◄شاشة اللمس: بلوحة (شاشة) لمس سعويه
◄Detect Point : 1 Finger
◄لون العرض: أبيض / أصفر / أزرق سماوي / أخضر

الرسم

2.7 inch 128x64 COG Capacitive Touch OLED Display with Frame +PCB - WEP012864Q-CTP
 

Data source ref: WEP012864QWPP3D00000

المواصفات

وظيفة دبوس واجهة التوصيل

No. الرمز الوظيفة
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)
This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT External interrupt signal, active low
24 TP_RST External reset signal, active low

البيانات الميكانيكية

العنصر الأبعاد الوحدة
مصفوفة نقطية 128 × 64
أبعاد الوحدة 82.0 × 47.5 × 8.65 Max. mm
المنطقة النشطة 61.41 × 30.69 mm
حجم النقطة 0.45 × 0.45 mm
درجة النقطة 0.48 × 0.48 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 حمولة
IC SSD1309
الواجهة 6800,8080,4-Wire SPI,I2C
الحجم 2.7 بوصة ‎‎
CTP IC GT911
Detect Point 1
CTP الواجهة I2C
السطح توهج

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Logic VDD -0.3 4 V
درجة حرارة التشغيل TOP -20 +70 °C
درجة حرارة التخزين TSTG -30 +80 °C

المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VDD =3V 175 350 mA
 

Touch Panel Controller GT911

العنصر الرمز أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 0.25xVDD V
Output High Volt. VOH 0.85xVDD V
Output Low Volt. VOL 0.15xVDD V
go top
close