نزل المنتجات وحدات OLED شاشات جرافيك OLED WEO128128D-CTP

رقم الموديل WEO128128D-CTP

◄النوع: جرافيك
◄االهيكل: COG
◄الحجم: 1.18 بوصة
◄مصفوفة نقطية 128*128
◄وحدة تحكم مدمجة SSD1327
◄مزود طاقة 3 فولت
◄1/128 حمولة
◄الواجهة: SPI, I2C
◄ بلوحة (شاشة) لمس سعويه
◄Detect Point : 1 Finger
◄لون العرض: أبيض / أصفر / أزرق سماوي (have high MOQ)
◄Support Grayscale

الوصف

 

الرسم

1.18" 128x128 Round OLED Display Module with Touch Screen - WEO128128D-CTP
Data source ref: WEO128128DWPP3D00001

المواصفات

وظيفة دبوس واجهة التوصيل

No. الرمز الوظيفة
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select.
Bus Interface selection
BS1 Interface
0 4-line SPI
1 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 IREF This pin is the segment output current reference pin
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 DC# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, will be interpreted as data.
When the pin is pulled LOW, will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection.
11 D0 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL.
12 D1
13 D2
14 TP_SCK I2C clock signal
15 TP_SDA I2C data signal
16 TP_INT Interrupt signal
17 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
18 VSS Ground

البيانات الميكانيكية

العنصر الأبعاد الوحدة
مصفوفة نقطية 128 × 128 Dots
أبعاد الوحدة Ø50.5 × 5.0 mm
المنطقة النشطة Ø30.0 mm
حجم النقطة 0.210 × 0.210 mm
درجة النقطة 0.235 × 0.235 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/128 حمولة
Gray Scale 4 bits
IC SSD1327
الواجهة 4-line SPI , I2C
الحجم 1.18 بوصة
PCAP IC IT7259
Detect Point 1
PCAP Interface I2C
PCAP Surface Hardness 6H

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Operation VCI -0.3 4.0 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 19.0 V
درجة حرارة التشغيل TOP -20 +50 °C
درجة حرارة التخزين TSTG -30 +70 °C

المميزات الإلكترونية

DC المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VCI 2.8 3.0 3.3 V
Supply Voltage for Display VCC 14.0 14.5 15.0 V
High Level Input VIH 0.8×VCI VCI V
Low Level Input VIL 0 0.2×VCI V
High Level Output VOH Iout = 100uA 0.9×VCI VCI V
Low Level Output VOL Iout = 100uA 0 0.1×VCI V
50% Check Board operating Current VCC =14.5V 24 36 mA

 

Touch Panel Controller IT7259

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Input High Volt. VIH COMS 1.2 V
Input Low Volt. VIL COMS 0.5 V
Output High Volt. VOH IOH = 2mA 2.4 V
Output Low Volt. VOL IOL = 2mA 0.4 V
go top
close