نزل المنتجات وحدات OLED شاشات جرافيك OLED WEO012864Q

64x128 وحدات شاشات جرافيك OLED

رقم الموديل WEO012864Q

◄النوع: جرافيك (بدون إطار)
◄االهيكل: COG
◄الحجم: 2.7 بوصة
◄مصفوفة نقطية 128*64
◄وحدة تحكم مدمجة SSD1309ZC
◄مزود طاقة +3 فولت
◄1/64 حمولة
◄الواجهة: 6800/8080/SPI/I2C
◄لون العرض: أبيض / أصفر / أزرق سماوي / أخضر

الرسم

Winstar Display - 2.7", 128x64, Monochrome Graphic OLED Display

المواصفات

وظيفة دبوس واجهة التوصيل

.No الرمز الوظيفة
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS
4 IREF This pin is the segment output current reference pin. IREF is supplied externally
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus
Unused pins are recommended to tie LOW
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout
SDAin in application and D0 is the serial clock input, SCL
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected
When serial or I2C interface is selected, this pin must be connected to VSS
14 R/W# This pin is read / write control input pin connecting to the MCU interface
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected
When serial or I2C interface is selected, this pin must be connected to VSS
15 D/C# This pin is Data/Command control pin connecting to the MCU
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection
When 3-wire serial interface is selected, this pin must be connected to VSS
16 RES# This pin is reset signal input
When the pin is pulled LOW, initialization of the chip is executed
Keep this pin pull HIGH during normal operation
17 CS# This pin is the chip select input connecting to the MCU
(The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation
22~28 NC No connection
29 VSS Ground
30 NC No connection

البيانات الميكانيكية

العنصر الأبعاد الوحدة
مصفوفة نقطية 128 × 64
أبعاد الوحدة 73.0 × 41.86 × 2.05 mm
المنطقة النشطة 61.41 × 30.69 mm
حجم النقطة 0.45 × 0.45 mm
درجة النقطة 0.48 × 0.48 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 حمولة

المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13 13.5 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 22 24 mA
go top
close