نزل المنتجات وحدات OLED شاشات جرافيك OLED WEO012864AJ

رقم الموديل WEO012864AJ

◄النوع: جرافيك
◄االهيكل: COG
◄الحجم: 2.42 بوصة
◄مصفوفة نقطية 128*64
◄وحدة تحكم مدمجة CH1116
◄مزود طاقة +3 فولت
◄1/64 حمولة
◄الواجهة: I2C,4-line SPI,8-bits 6800/8080 parallel
◄لون العرض: أبيض / أصفر
◄MOQ:150K

الوصف

الرسم

2.42 inch OLED, 128x64 SPI OLED Display - WEO012864AJ
Data source ref:WEO012864AJWPP3N00000

المواصفات

وظيفة دبوس واجهة التوصيل

No. الرمز الوظيفة
1 NC(GND) No connection
2 VSS Ground.
3-10 NC No connection
11 VDD1 Power supply input
12 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
13 IM2
14 NC No connection
15 CS# This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.
16 RES# This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
17 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
18 WR#
(R/W#)
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#= “H”: Read.
When R/W#= “L”: Write.
19 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# = “H”: Enable.
When RD# = “L”: Disable.
20~27 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
28 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
29 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
30 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
31 NC(GND) No connection

البيانات الميكانيكية

العنصر الأبعاد الوحدة
مصفوفة نقطية  128 × 64 نقطة
أبعاد الوحدة 60.5 × 37.0 × 2.11 mm
المنطقة النشطة 55.01 × 27.49 mm
حجم النقطة 0.40 × 0.40 mm
درجة النقطة 0.43 × 0.43 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 حمولة
IC CH1116
الواجهة I2C,4-line SPI,8-bits 6800/8080 parallel
الحجم 2.42 بوصة

تصنيفات الحد الأقصى المطلق

Parameter لرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VCC 0 14.5 V
درجة حرارة التشغيل TOP -40 +80 °C
درجة حرارة التخزين TSTG -40 +85 °C

المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD1 1.65 3.0 3.3 V
Supply Voltage for Display VPP 6.4 13.0 13.5 V
High Level Input VIH 0.8×VDD1 VDD1 V
Low Level Input VIL VSS 0.2×VDD1 V
High Level Output VOH 0.8×VDD1 VDD1 V
Low Level Output VOL VSS 0.2×VDD1 V
Display 50% Pixel on IPP VPP =13V 15 30 mA

 

go top
close