نزل المنتجات وحدات OLED شاشات جرافيك OLED WEO009632B

رقم الموديل WEO009632B

◄النوع: جرافيك
◄الهيكل: COG
◄الحجم: 0.68 بوصة
◄مصفوفة نقطية 96*32
◄وحدة تحكم مدمجة SSD1305
◄مزود طاقة +3 فولت
◄1/32 دورة الحمولة
◄الواجهة: 6800, 8080, SPI, I2C
◄لون العرض: أبيض / أصفر
◄Other FPC options available in below table

الوصف

الرسم

WEO009632B with ZIF FPC

96x32 OLED Graphic Display 0.68 inch - WEO009632B-ZIF

Data source ref: WEO009632BLAP3N00000
 

WEO009632B with Hotbar FPC

0.68 inch COG Graphic Display with Hotbar FPC - Winstar Display

Data source ref: WEO009632BWPP3N00H00

المواصفات

وظيفة دبوس واجهة التوصيل

Pin الرمز I/O الوظيفة
1 VSS - Reserved Pin(Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 GDR - Reserved pin, not connected.
3 VDDB P Reserved pin, not connected.
4 FB - Reserved pin, not connected.
5 NC - Not connected.
6 VBREF - Reserved pin, not connected.
7 NC - Not connected.
8 NC - Not connected.
9 VDD P Power supply pin for core logic operation.
10 BS1 I MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, and BS1 are pin select.
  4-line SPI I2C 8-bits 8080 8-bits 6800
BS1 0 1 1 0
BS2 0 0 1 1
11 BS2 I
12 NC - Not connected.
13 CS# I This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# I This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# I This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
16 WR# I This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# I This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 - These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF - This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
27 VCOMH - COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC - Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.

البيانات الميكانيكية

العنصر الأبعاد الوحدة
دقة العرض 96 × 32 نقطة
أبعاد الوحدة 19.80 × 12.32 × 1.21 (mm) mm
المنطقة النشطة 16.298 × 5.418 (mm) mm
حجم النقطة 0.148 × 0.148 (mm) mm
درجة النقطة 0.17 × 0.17 (mm) mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/32 Duty
IC SSD1305
الواجهة 6800, 8080, SPI, I2C
الحجم 0.68 بوصة

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 16 V
درجة حرارة التشغيل TOP -40 +80 °C
درجة حرارة التخزين TSTG -40 +85 °C

المميزات الإلكترونية

DC Characteristics

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 11.5 12 12.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH Iout = 100uA 0.9×VDD VDD V
Low Level Output VOL Iout = 100uA 0 0.1×VDD V
 
الرمز Parameter أدنى قيمة لقيمة النموذجية أقصى قيمة الوحدة الحالة
ICC VCC Supply Current - 5.0 7.5 mA VDD =3.0V , Display 100% ON

FPC Options:

Drawing FPC Length PIN pitch ZIF FPC or HOTBAR FPC Interface FPC No. Create Date
FPC2050002811XXXXX01_WEO009632BWAP3N00000 30 28 0.5 ZIF FPC 6800, 8080,4-Wire SPI, I2C FPC2050002811XXXXX01 20180131
FPC2065002501XXXXX00_WEO009632BWPP3N00H00 8.479 25 0.65 HOTBAR FPC 6800, 8080,4-Wire SPI, I2C FPC2065002501XXXXX00 20190906
go top
close