نزل المنتجات وحدات OLED شاشات جرافيك OLED WEO009664B-ZIF

رقم الموديل WEO009664B-ZIF

◄النوع: جرافيك
◄الهيكل: COG+ ZIF FPC
◄الحجم: 1.1 بوصة
◄مصفوفة نقطية 96*64
◄وحدة تحكم مدمجة SSD1327
◄مزود طاقة +3 فولت
◄1/64 دورة الحمولة
◄الواجهة: 6800/8080/SPI/I2C
◄لون العرض : أبيض / أصفر

الوصف

الرسم

Small OLED Screen, OLED Display Screen, 1.1 OLED Screen Module - WEO009664B

المواصفات

وظيفة دبوس واجهة التوصيل

No الرمز الوظيفة
1 VSS .Ground pin. It must be connected to external ground
2 VCC .Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source
3 VCOMH .COM signal deselected voltage level
.A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin
4 VCI .Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source
.VCI must always set to be equivalent to or higher than VDD
5 VDD .Power supply pin for core logic operation
6 BS1 .MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
Bus Interface selection
[BS[2:1 Interface
0 4 line SPI
1 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel

Note (1) 0 is connected to VSS (2) 1 is connected to VCI
7 BS2
8 VSS .Ground pin. It must be connected to external ground
9 IREF This pin is the segment output current reference pin
10 #CS .This pin is the chip select input connecting to the MCU
.(The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW
11 #RES .This pin is reset signal input
.When the pin is pulled LOW, initialization of the chip is executed
.Keep this pin pull HIGH during normal operation
12 #D/C .This pin is Data/Command control pin connecting to the MCU
.When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data
.When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register
.In I2C mode, this pin acts as SA0 for slave address selection
.When 3-wire serial interface is selected, this pin must be connected to VSS
13 #R/W .This pin is read / write control input pin connecting to the MCU interface
.When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW
.When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected
14 E .This pin is MCU interface input
.When 6800 interface mode is selected, this pin will be used as the Enable (E) signal
.Read/write operation is initiated when this pin is pulled HIGH and the chip is selected
.When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected
.When serial or I2C interface is selected, this pin must be connected to VSS
15 D0 .These pins are bi-directional data bus connecting to the MCU data bus
.Unused pins are recommended to tie LOW
.When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC
.When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC .Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source
24 VSS .Ground pin

البيانات الميكانيكية

العنصر الأبعاد الوحدة
مصفوفة نقطية 96 × 64 نقطة
أبعاد الوحدة 29.00 × 22.50 × 1.65 mm
المنطقة النشطة 22.53 × 15.01 mm
حجم النقطة 0.205 × 0.205 mm
درجة النقطة 0.235 × 0.235 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 حمولة
IC SSD1327
الواجهة 4-Wire SPI, I2C, 6800, 8080
الحجم 1.1 بوصة

المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VCI 2.8 3.0 3.3 V
Supply Voltage for Display VCC 8.0 8.5 9.0 V
Input High Volt VIH 0.8×VCI VCI V
Input Low Volt VIL VSS 0.2×VCI V
Output High Volt VOH 0.9×VCI VCI V
Output Low Volt VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=8.5V 13.0 26.0 mA

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Operation VCI -0.3 4.0 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 19.0 V
درجة حرارة التشغيل TOP -40 +80 °C
درجة حرارة التخزين TSTG -40 +85 °C

Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1 inch oled, oled 1.1, oled 1.1
go top
close