10.2" TFT LCD, Industrial TFT LCD
Model No. WF102QTIFGDBT0
►Size : 10.2 inch
►Resolution : 800 x 480 dots
►View Direction : 12H
►Interface : MCU
►Controller IC：SSD1963
►Control-Board : Yes
►Brightness(cd/m2) : 250
►Frame Through Hole : No
►Touch Screen : Resistive Touch Panel (RTP)
Description
The WF102QTIFGDBT0 TFT-LCD is a 10.2" of Winstar TFT Q series family. The WF102Q series which is with SSD1963 controller board plus a 36 pin-out connector on board. This 10.2" TFT LCD model is featured with 8 bit or 16 bit options and already defined pin no. 33 ~ 36 as backlight supply; therefore, the customers no need to design extra backlight circuit. This display is with the module dimension of 235.0 × 145.8 mm and AA size of 222.0 × 132.48 mm. The key Advantages of TFT Q Series are as below:
- Winstar Q Series integrated a 36 pin-out connector on SSD1963 controller board and all connectors are the same direction.
- Q Series modules are available in 8 bit and 16 bit parallel interface options.
- The pin no. 33 ~ 36 already pre-defined as backlight supply.
- Built in backlight driver IC, Q series TFT displays can be drive by 5.0V (3.5" and 4.3"also support 3.3V). The customers do not have to change the backlight driver circuits while change the TFT module sizes.
- The 5.7", 7.0", 8.0" and 10.2" Q Series are allowed to design Sleep Mode to close BIAS(VGH, VGL, AVDD) low power consumption mode.
- Resistive Touch Screen options are available for all Q Series TFT display, and 4-Line signal (X1, Y1, X2, Y2) can be input from 36pin connector.
DRAWING
SPECIFICATIONS
Interface
| Pin | Symbol | Function |
|---|---|---|
| 1 | GND | System ground pin of the IC . Connect to system ground. |
| 2 | VDD | Power Supply : +3.3V |
| 3 | BLE | Backlight control signal , H: On \ L: Off |
| 4 | D/C | Data/Command select |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7~14 | DB0~DB7 | Data bus |
| 15~22 | DB8~DB15 | Data bus (When select 8bits Mode, this pin is NC) |
| 23~24 | NC | No connect |
| 25 | CS | Chip select |
| 26 | RST | Hardware reset |
| 27 | L/R | Left / right selection; Default L/R=H |
| 28 | U/D | Up/down selection; ; Default U/D=L |
| 29 | XL | Left electrode |
| 30 | YU | Top electrode |
| 31 | XR | Right electrode |
| 32 | YD | Bottom electrode |
| 33~34 | VLED- | Power for LED Driver IC(GND) |
| 35~36 | VLED+ | Power for LED Driver IC(+5V) |
General Specifications
| Item | Dimension | Unit |
|---|---|---|
| Size | 10.2 | inch |
| Dot Matrix | 800 × RGB × 480 | dots |
| Module dimension | 235.0(H) × 145.8(V) × 12.4(D) | mm |
| Active area | 222.0(W) × 132.48(H) | mm |
| Dot pitch | 0.0925(W) × 0.276(H) | mm |
| LCD type | TFT, Normally White, Transmissive | |
| View Direction | 12 o'clock | |
| Gray Scale Inversion Direction | 6 o'clock | |
| Backlight Type | LED, Normally White | |
| Controller IC | SSD1963 | |
| Interface | Digital 8080 family MPU 8bit/16bit | |
| Touch Screen | Resistive touch screen (RTP) | |
| Surface | Anti-Glare | |
Absolute Maximum Ratings
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
Electrical Characteristics
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage For LCM | VDD | － | 3.0 | 3.1 | 3.3 | V |
| Supply Current For LCM | IDD | － | － | 160 | 225 | mA |
Search keyword: tft 10.2, tft 10.2", 10.2 tft lcd, 10.2" tft lcd, 10.2 inch tft lcd, tft lcd 10.2, 10.2 tft display, 10.2" tft display, 10.2 inch tft display, tft display 10.2, tft display 10.2"
